Thursday, January 18, 2018

How to sew your Quilt Binding continuously around the corner - Tutorial


Its funny how the little things in quilting can be overlooked!  I teach lots of students how to Quilt and sometimes it those "smaller" tips or the things you think people know how to do, that students find often the most helpful.  When I teach and show students about "How to sew your Binding - continuously around the corner" this always raises eyebrows and usually big gasps of "why didn't I know this!"  After sharing this tip the other day on my Instagram Stories - (@tiedwitharibbon) it turns out that a lot of people didn't know this little trick so I thought I would share it with you.  

(This tip is only one part of the Binding process and not a full tutorial on how to bind your Quilt. You can find one I have done here)



When I first learned how to quilt - I used to sew my binding to the front of my quilt and then as I got to the corner (where I was going to mitre it) I would stop 1/4 of an inch before the end, take the quilt out of the sewing machine, make the mitre with the binding, pin it in place, then place it back in my machine to continue to sew before reaching the next corner and then repeating.  That was until I was shown this way about 6 years ago and I have never done it any other way since....

Note: I prefer to sew the Binding onto my Quilt with the batting and backing excess still as one piece - I don't trim this off before binding and I have even asked my Quilter not to trim the excess batting and backing of my quilts so I can Bind them this way.

I also like to colour match my thread!  Use threads to blend with the Top Thread to match the Binding fabric colour and the Bobbin Thread to match the quilt Backing fabric colour.


Step 1 - Use an Erasable Fabric marker to square up your quilt by marking a line around your quilt that makes the quilt Square, making sure to take into account your 1/4in seam allowance.


Step 2 Starting along one side of your Quilt take your made Binding and sew the Binding strip to the right side of your quilt.  To Mitre your Quilt corners in one continuous sequence stop 1/4in before you reach the corner of your quilt.  



Step 3 - Put the "Needle Down" into the quilt, lift the Presser Foot and rotate the quilt around 90 degrees.  Place the Presser Foot back down.


Step 4 - Reverse Stitch back to the edge of the quilt top (I find this is about 3 stitches on my machine).  Place your "Needle Down" again.


Step 5 - Lift your Presser Foot up and fold the binding at a 90 degree angle away from your Quilt top covering the angle you have created.  



Step 6 - Line up the raw edges of your Binding along the raw edge of your Quilt top.  Place the Presser Foot back down and sew along the next side of your Quilt.


Step 7 - Continue to sew your binding all the way around your Quilt.  Once you have sewn it all the way around you can then trim the excess batting and binding.  The reason I do not trim this before binding is so that you can leave enough to fill to the centre binding line, before being folded over and sewn to the back seam line of your quilt.




I hope you find that Helpful - leave a comment below. I'd love to know what tips and tricks of quilting you would love to find out about.

PS - Thanks to Carol Brady of The Quilting Cottage for your awesome Long Arm Machine Quilting of this quilt.

Thread - Aurifil #5005 (top) and #2615 (backing)
Machine - Pfaff Performance 5.0

Happy quilting

20 comments:

  1. Thanks for sharing a great tip. Ki hadn’t seen thi idea before. I’m just about to start binding my next quilt, so will give it a try.

    ReplyDelete
    Replies
    1. You are very welcome Janice - hope it makes binding just that much quicker for you for you next project.

      Delete
  2. I will use this method first on a sample sandwich to see how it goes. Sounds good, thanks.

    ReplyDelete
  3. Oh my this is genius! Every time I think I’ve seen all the ways to do binding, another one pops up that’s brand new to me! Thank you for sharing this! I’ll definitely be trying this next time! May I ask if you leave ¼ inch batting or ⅜? Just curious. Thanks again 😊

    ReplyDelete
    Replies
    1. My pleasure Donna, hope its helpful, usually the extra batting is about an 1/8in past the binding strip - just enough to fill to the centre crease of your binding strip

      Delete
  4. Great tip! I will try this the next time I bind a quilt!

    ReplyDelete
  5. This is genius! Thank you for sharing. I have always stopped and cut the threads, then restarted, otherwise very much the same way. I don't know why this never occurred to me. Quick question - do you have your binding on a spool on top of your machine? How is that done? Looks like a fine idea.

    ReplyDelete
    Replies
    1. Hi Linda, funny how the little things make the big difference sometimes. The Spool that the Binding Baby is sitting on is the inbuilt top loading Spool pin on my machine - it lift up if you want to place a thread spool vertically or perfect for the Binding Baby. If you head to Dohicky's Website they have some videos. Hope that helps. Jemima

      Delete
  6. I'm blown away. That was so simple. Thanks for sharing.

    ReplyDelete
  7. I machine stitch my binding down so I typically sew it to the back then flip to the front to stitch down with a 1/8" seam. Do you think your method would work ok with the quilt top trimmed square prior to binding being applied?

    ReplyDelete
  8. I think that you need the extra surface to "park" the needle on when you pivot, otherwise the quilt would skitter around and you wouldn't get a clean mitre.

    ReplyDelete
  9. Great idea! One question - how do you connect the two end pieces together?

    ReplyDelete
  10. This is one of those "OMG-why-didn't-that-occur-to-me-earlier" moments! THANK YOU :) :) :)

    ReplyDelete
    Replies
    1. Definitely one of those its so obvious but until someone shows you tips right

      Delete
  11. Totally going to try this! Thank you!

    ReplyDelete
  12. I like this! I just got over my fear of binding, and now enjoy it. This will make it even easier!
    I understand the whole tutorial EXCEPT for this: "The reason I do not trim this before binding is so that you can leave enough to fill to the centre binding line, before being folded over and sewn to the back seam line of your quilt." Could you explain this to me please?

    ReplyDelete
  13. Excellent tutorial. One question. After you have done the back and flip it over there seems to be extra fabric in the corners. Do you trim the corners?

    ReplyDelete

Note: Only a member of this blog may post a comment.

Related Posts Plugin for WordPress, Blogger...